Description

Our famous Bolt-On Pinto Mustang II Crossmember kit for 1940 Chevy Car.

Safety Thru Engineering.
Handmade in the USA.
Exclusive adjustment system.
Interlocking design.
Superior strength.
Easy and accurate installation.
Correct geometry.

Strut rod mounts are available on the IF-4040CP-SR

This custom-made fully bolt-on crossmember kit is based on the Pinto-Mustang II independent front suspension system. Adding this kit to your ride eliminates bump steer and other unpleasant surprises resulting in a safe and enjoyable ride. The crossmember itself lowers your car about 2-4 inches when compared to stock, and with the adjustable upper coil spring pods there is about 2 1/2″ of additional adjustment possible to further fine tune your setup, providing the best method available to get the correct height geometry. Center support rods provide additional strength to the lower strut rod mount, and the interlocking tabs between upper pods and lower crossmember prevent movement.

Safety thru Engineering: This fully bolt-on crossmember uses Pinto-Mustang II based suspension components. Using our 50+ years of expertise and experience, we have engineered this system to provide your classic ride with a suspension that is far superior to that of the original Mustang II in safety, strength, handling and performance. Interlocking design: The main bolt-on crossmember cradles the frame for superior strength.

Adjustment System: Our exclusive ride height adjustment system enables about 2 1/2″ of adjustable height at the coil spring pods, providing the best method for correct ride height geometry or to fine-tune your ride. Note: The adjustment system provides a quick and easy way to correct the driving geometry of your ride. The crossmember itself will lower your ride 2-4 inches from stock. It is important to keep the lower A-arms level. Our adjustment system allows you to set up the suspension correctly and then adjust as needed as the car settles.

Easy and accurate installation: Build using the highest quality standards, our independent front suspension is easy to install. The unique bolt-on system can be mounted safely and securely, and with the included instructions, installation of the crossmember is just a matter of following a couple of steps. The super-accurate fixtures we use when building your crossmember ensure a perfect fit.

Recommended parts: Complete hub-to-hub component package, IF-7480TWP (power rack version) or IF-7480TWM (manual rack version), when combined with this crossmember, builds a complete front end. Kit includes new custom made upper and full lower control arms, spindles with nuts, caliper bracket kit, 11″ rotors, calipers with pads and pins, coil springs, manual rack and pinion, rack bushings, tie rod ends and shocks. The full lower control arms eliminate the need for support rods.

Complete hub-to-hub component package, IF-7480HHP (power rack version) or IF-7480HHM (manual rack version), when combined with this crossmember builds a complete front end. Kit includes new custom made upper and lower control arms, strut rods with bushings, spindles with nuts, caliper bracket kit, 11″ rotors, calipers with pads and pins, coil springs, manual rack and pinion, rack bushings, tie rod ends and shocks.

To fine-tune our ride height adjustment system easily, consider our custom IFS wrench. Set-up rods that temporarily replace the shocks and springs for an easy way to set the correct ride height during the build. For use with a small block engine, we recommend using 325lb coil springs, but others are available as well.

Installation Instructions for IF-4040CP Pinto/Mustang IFS for 1940 Chevy Car Step

1. Unbolt and remove original front crossmember. Straighten frame lips where new crossmember and strut rods will sit. Remove any rivet heads that may interfere with fitting. Grind heads flush with frame.
Step 2. Clamp new lower crossmember in place using the four 3/8″ holes that match the original crossmember holes,  You may need to pull the frame horns together. Steering mounts on crossmember go to the front. Install the four bolts and tighten.
Step 3. Place the coil spring pods over the frame and line them up with the lower crossmember. The pods will only fit one way, the taller side goes to the front. Check for clearances between the frame and the new parts and correct any interference problems found. At this point we recommend that you check for tire centering. Assemble the A-arms and spindle on one side (without a spring) and install a wheel. Visually check for centering. In the (unlikely) event of a miss, the crossmember can be moved up to 1/2″. Wheel centering is normally not a problem, but it is always better to check.
Step 4. Clamp upper and lower pieces together and in place. Again, check the fit. When drilling new holes, do the (8) vertical holes first, using the crossmember as a drill guide. Insert the bolts and tighten. Now drill the holes in the sides (8 per side), insert the bolts and tighten them.   The crossmember, frame and pods should now be firmly attached to each other.
Step 5. Strut rod support brackets are next. Straighten the frame edges to 90 degrees. Put bracket in place around the frame and insert a bolt in the center brace to crossmember tube. Now fit the bracket to the frame and locate the spot where the bracket fits the frame the best. Do both sides, compare both measurements and make them the same. Brackets will fit the frame exactly only if the frame is straight and bottom lip is 90 degrees to the side.
Step 6. Drill underneath holes first, keeping brackets flush with the outside of the frame. Do outside holes then the inside holes, bolting them as you go.
Step 7. Install components from 1974-1980 Pinto/1974-1978 Mustang II to complete the installation. Manual steering is recommended. Use Pinto strut rods, no Mustang strut rods. Use a new strut rod bushing set. See Ford Front-End manuals for installation instructions covering A-arm, strut rods, springs, shocks and lineup specs. Cut your coil to 12″ height. (Chassis Engineering coil springs are sized properly).Chassis Engineering has springs available in 25lb increments
Step 8. To adjust the height, first take off all the weight off of the springs. This means jacking up the front wheels of the ground and possibly unhooking the shocks. Caution: To prevent injury be sure to use jack stands to support the car anytime you may be working under it. Loosen 1/4″ locking set screw and turn height adjuster to new position. The adjustment can be used for different springs. For correct geometry, the lower A-arm should be parallel to the ground. Line up groove in threads and re-tighten locking set screw.
Step 9. The final step, after height adjustment is to have the front end aligned to Pinto specs.
Step 10.  once a “fresh” car with a new IFS gets some good road miles, it may become necessary to once again adjust the IFS spring pods due to normal settling of the new front coil springs. The lower control arms must maintain a “parallel to the ground” stance for good geometry and prolonged ball joint life. When making such an adjustment remember to loosen the set screw and add a little anti-seize compound before turning down the spring adjuster. Removing the shock and use of a spring compressor will also aid in this procedure. To aid in adjusting your IFS, we offer the IF-0000W adjustment wrench. Afterwards, reinstall the shock and tighten the set screw.

WARNING: This product can expose you to chemicals including nickel and urethane, which are known to the State of California to cause cancer and birth defects or other reproductive harm.  For more information go to www.P65Warnings.ca.gov.